21 March 2025 – Cartagena Boat Projects

We went to the symphony! Our friend Rob was feeling ill, so he gifted us their tickets to a full symphony orchestra playing at the El Batel less than 100m from where we are berthed at Yacht Port Cartagena. What could be better?

Anchor Shank Lockdown Project

Manuel finished welding the last pieces I needed for the bow and anchors. In the past, I used two SS locking pins to secure the anchors while underway, but on the ocean – that was never enough. With big waves, the anchors might move a little, and bang as they did so. This is what he made for me, based on my plans.

In place, I can tighten down on each of the butterfly nuts and separately secure the shank of each anchor. I have only tried it in the marina, but it seems strong enough. I put some rubber hose on the SS, so it’s not a metal-on-metal contact.

Top view.

Front and aft views.

Chain Counter Project

When I first built the boat, I installed an IDEAL vertical windlass with only one means of operation: two deck switches, UP and DOWN. Over the years, I wished to have another means of operating the windlass, so when in India in 2019, I installed a wireless controller, and that worked pretty well. However, I have come to envy those few boat owners who can actually control their windlass from the helm, and have a chain counter in place. After some research, I first picked a CruzPro model (made in NZ), but instead opted for a Quick CHC Chain Counter (made in Italy) because it was easier to obtain.

Placing the magnet and sensor was the easy part. I drilled a hole in the gypsy (chain wheel) chain stripper, epoxied the sensor in place and directed a wire pair out front and through the deck. In this photo, the wire is encased inside a rubber hose for protection. The magnet is easy to spot, because I highlighted it with a black sharpie, so it was easy to see during the calibration. I drilled a hole through the gypsy housing, and epoxied the magnet in place. Quick supplied a very small rare earth conducting magnet, but I replaced it with a bigger one that I bought from Lee Valley in Canada over 20 years ago. One turn of the gypsy, or chain wheel, corresponds to 37.5cm of chain travel. The sensor and magnet combination work very well.

During installation, a few weeks ago, I ran into a stumbling block. I was getting error messages “opposite commands”. The manufacturer said that it was due to a bad, or misplaced ground, but was unable to narrow this down any further. After reviewing the circuit diagrams and thinking about this for some time, I finally figured out that the reason for the error, and malfunction of the display was that my IDEAL windlass setup uses a double solenoid with a single negative trigger to switch between two positive outputs to the reversing motor—one for up, one for down. All of the switches (foot, helm, and wireless) apply that negative signal to the solenoid to control direction. The Quick CHC Chain Counter, on the other hand, expects a positive voltage signal from any switch to tell it the windlass is running and in which direction, pairing that with the gypsy magnet and sensor to track chain movement. Since my system doesn’t naturally provide a positive signal at the switch level, the chain counter was not getting the directional cue it needs.

Have you started to use AI much? I downloaded Grok 3 on my phone and laptop a month ago, and have used it daily since then. Last week, I engaged in a very detailed conversation with Grok 3 about this very problem, and Grok was instrumental in developing a simple, cost-effective solution for me – within seconds.

The core issue is that the chain counter’s “passive” nature means it’s designed to monitor switch inputs that directly send positive voltage to a windlass or solenoid, not to interpret a negative-triggered solenoid output. My negative-sense system inverts the control logic compared to what the CHC expects – and that is why I was getting the error messages “opposite commands”.

The practical solution is to use two 12V SPDT (single-pole, double-throw) relays to translate the negative signals from my switches into positive signals for the chain counter.

I bought two 12V automotive relays (5-pin SPDT, commonly ~$5 each) rated for 40A. They will only be passing 2-4A, but I’d rather err on the side of caution.

For each relay:

  • Pin 30 (common): Connect to +12V from my bus.
  • Pin 87 (normally open): Connect to the Chain Counter (CHC) monitor “up” or “down” input wire
  • Pin 85 (coil): Connect to the negative wire from my switch (one relay for “up” switch, one for “down”).
  • Pin 86 (coil): Connect to +12V.
  • Pin 87a (normally closed): Leave unconnected.

How it works:

When you press the “up” foot switch, it grounds the solenoid’s “up” coil and also the relay’s coil (Pin 85). The relay energizes, connecting Pin 30 (+12V) to Pin 87, sending a +12V signal to the CHC’s “up” input. The same deal applies for “down” with the second relay. When no switch is pressed, the relay stays off, and no voltage goes to the CHC. The CHC now sees +12V when the windlass runs, matching its positive-sense logic.

The primary reason that I’ve gone into so much detail here, is that a lot of people come across my blog based on word searches, and my solution is bound to be of help to someone with a similar issue.

Here is a copy of the complete windlass wiring, without these two relays.

Here is a copy of the relay wiring diagram.

It is a simple and cheap fix, and now my Quick CHC chain counter works. The new display at the helm (including new bow thruster rocker switch, new clock and new windlass rocker switch) will display which direction the windlass is turning and how many feet of chain is out.

Chain Wash Solution

Another thing that I have been thinking about for several years is some form of automatic chain washing that doesn’t involve me holding a hose, and pointing it at the chain. When on the deck and bringing up the anchor and chain, I frequently have a lot of things going on. For me, it was desirable to achieve some form of automation. A few years ago, I simply tied in place the wash down pump hose (sea water) to direct spray at the chain as it was coming up over the bow roller. This worked great until the anchor came up, and knocked into the nozzle. Of course, I also needed to direct the spray to clean off the anchor and no longer the chain. To this end, I have finally come up with what I believe is a good solution. I bought a GARDENA plastic fitting that splits the pressurized sea water into two streams, one for direct chain wash, and one for the hand-held hose to wash the anchor.

This is a deck view of the finished installation.

Here is a side view of the installation.

Here is a picture of the 1/8”NPT fitting nozzle that I am using for direct chain wash – in action. It is very well positioned, and easily adjustable.

This should make things simpler and more effective when we are picking up the anchor.

Chain Fall Project

Another important issue that we have been struggling with for years – has been chain fall. When the chain is brought in, almost always – the chain does not “fall” neatly into the chain locker and someone needs to be inside the fore cabin and poking the chain, so it doesn’t block up. Many, many cruisers struggle with the same issue, and I believe we have finally solved it. The weight of chain provides the momentum for it to fall and pile. So, the solution always involves dropping the chain into a central spot and raising the drop point as high as practicable. When building the boat back in Kingston during the timeframe 1998-2002, I used some PVC electrical conduit to operate as a “chain slide”. This is what the chain fall looked like just a few months ago.

I had Manuel (my local welder) make up a SS316 pipe with a very specific length and curve, in order to relocate the drop point about 5-6 inches higher than previous. This is what it looks like installed, with no chain in it.

After operating it with chain, we have realized that this is most probably going to be a workable solution. The SS316 metal is more slippery than the PVC was, and particularly when it’s wet. Here is the end result, with the chain piled up to the zero point.

New USB-C outlets.

There are many 12V socket type connections inside our boat, in order to connect to electronic devices. For years, we have been using just USB-A plugs fitted to 12V sockets, but now with the proliferation of USB-C on the market, I decided it was time to upgrade to fixed USB-C and USB-A sockets, and not just 12V sockets. This way, they don’t wiggle around and disconnect on their own. This picture shows the old socket on the left, together with a new socket on the right.

2 March 2025 – Road Trip to Granada

We just came back from a 3 day road trip to Granada, about a 3 hour drive, door to door – with our friends Kevin and Sandy on SV NOCONA MOON. Along the way, we drove higher in elevation with the Sierra Nevada mountain range evident in the background.

Screenshot

In the afternoon, we took a city bus (about 50 cents per person) to the city centre and we hooked up with a tourist bus. We road around for the afternoon (it was rainy weather) and covered most of the city. This, we have found, is always a good way to get “the lay of the land”.

We passed through the streets and saw different parts of the city.

Oranges and lemons were growing on trees in most courtyards.

The next day, our first visit was to the Granada Cathedral. Like many other cathedrals in Andalusia, it was built on top of the city’s main mosque after the reconquest of Granada – in the early 1500’s. This cathedral took 181 years to build, not unusual in those times. This is a photo I took from the heights of the Alhambra, on the next afternoon.

While the Granada Cathedral is not the largest in the world, it is certainly very, very impressive. You cannot help but feel small, standing next to one of these columns.

In the cathedral, there were two organs, facing each other – and during our visit, the technicians were actually tuning them. It was a really special moment to be able to walk around, taking photos and listening to those ancient pipes.

The alter is massive, a photo cannot do it justice.

After leaving the Grenada Cathedral, we came across another treasure: “Five Guys Burgers and Fries”. Yes, it was fast food, and not Spanish, but it was really good, the best burger I’ve had in years!

The main event, of course, was to visit the Alhambra – an ancient palace and fortress complex located in Granada. Making YouTube videos is far too time consuming for me, but I will refer a good one when I think it will help to illustrate our experience. This one is about the Alhambra.

The Alhambra is one of the most famous monuments of Islamic architecture and one of the best-preserved palaces of the historic Islamic world – a very big tourist attraction in Spain. We bought the tickets more than a month ago, for a visit in the winter! There were lots of tourists, but our guide said it was not full. The complex construction was started in 1238 and took over 200 years to complete.

The Generalife Gardens were really something to behold, with the tall hedges, pools and trees. This, we were told, was a typical example of a Christian fountain.

This, on the other hand, was described as a typical Muslim fountain.

After the conclusion of the Christian Reconquista in 1492, the site became the Royal Court of Ferdinand and Isabella (where Christopher Columbus received royal endorsement for his expedition), and the palaces were partially altered.

Water is everywhere in the ornate and lavish Alhambra. It flows in channels that cool the buildings; spurts from fountains in grand rooms and charming courtyards; and sprays in such a way that, from certain angles, it perfectly frames majestic arched doorways. The same intricate system brings colour to the famed gardens of the Generalife gardens, the former summer palace next door. At the time of construction, this was one of the most sophisticated hydraulic networks in the world, able to defy gravity and raise water from the river nearly a kilometre below. The great innovation of the Nasrids was to design water ducting that would carry water 6km from the nearest river, and then uphill to their elaborate complex of courtyards, gardens and bath houses. This YouTube video serves to better explain how important the distribution of water is in the Alhambra.

This is the Palace of Charles V, inside the Alhambra.

This is an interior courtyard.

I took this photo inside the Comares Palace, to show the effect of water reflection, another example of the importance of water in the Alhambra.

These photos depict the Court of Lions.

On reflection, this Alhambra Palace (also known as the Red Fortress or Red Castle) is an impressive collection of buildings and courtyards, constructed over the ages. Initially built on Roman ruins, it was built by Muslim invaders who were subsequently driven out by the Christians. It has not only a well preserved fortress, but also the beautiful villa and gardens of the Generalife. The Alhambra is an essential monument, as it proves Arabs once ruled this territory and its architectural style is a relic of this former civilization.